I was managing the AP from a remote location's jumpbox which only has bare minimum tools since its a domain controller as well. The problem is that the AC240 page where it lists access points (when you connect to your primary AP) does not render properly in traditional Internet Explorer. I had looked everywhere in the access point (primary) and I never saw what was listed in the document above. Here is what has happened and it will no doubt affect others. What am I missing?Īlright the mystery has been solved, thank you pieterh for the help. Maybe its just me but I can't seem to find any decent documentation for these APs with respect to the LAN interfaces. Is this supposed to be key based auth and if so where do I set that up, no option for this in the user account page. How can I login via SSH? When I connect and enter my username I get "No supported auth methods available".
Configure ip address on ctivo mac#
Why do I have multiple LAN IPs and why is the IP that I am connecting to using the same MAC address as all of the other 240ac APs?ģ. How do I set a static IP for the AP after I have done the initial configuration, I can't find any options for configuring the LAN ports?Ģ. I have my network cable plugged into the PoE port which is connected to a Cisco 3750G switch. When I did the setup I configured it with a dynamic IP. I have done the initial setup and I am able to connect to the access point. Unfortunately my experience has been pretty bad so far with them and I am hoping its just my lack of information. Una vez aprovisionado y que se aplica y manda a reiniciar, valide con el comando SHOW AP ACTIVE, para validar que estuviera activo, sin embargo no lo esta.Hi I recently purchased a few 240ac APs and mesh extenders to replace an existing WAP321 deployment. Luego procedi a aprovisionarlo via GUIĬonfiguration / AP Installation / ProvisionĨ. Name Group AP Type IP Address Status Flags Switch IP Standby IP El AP se reinicia y posteriormente ya aparece el Agregue el AP con Cert Type: Factory-cert & State: Certified-factory-cert.Ħ. Así que en la Controladora aplique la recomendación del URL, que es dejar habilitado CPsec y luego agregar manualmente el AP a lista blanca: ( AP tiene MAC terminada en: BB 3A)Ĭonfiguration / AP Instala / Whitelist. (Investigue y explicaban que ese estado se debe a que esta habilitado por defecto CPsec)ĥ. Una vez conectado, revise con el comando SHOW AP DATABASE, y se indicaba el Status DENIED. (Previamente, había pasado el IAP a CAP, validando desde CLI que se tuviera conectividad hacia el IP 172.16.0.254Ĥ. Así que conecte con un cable de conexión directa del puerto 0 del Controller hacia el Puerto ENET del AP 215. Venía con un reset default, le configure los parámetros por defecto, VLAN 1, 172.16.0.254/24 (IP Controller), y adicionalmente habilite el DHCP Server con el Pool 172.16.0.0/24ģ. Les comparto los resultados con otra Controladora 7010ġ. R = Remote AP R- = Remote AP requires Auth C = Cellular RAP c = CERT-based RAP 1 = 802.1x authenticated AP 2 = Using IKE version 2 You get a big denied when an AP is denied: Would be helpful if DEV is going to use a flag to give us an idea what it does. R = Remote AP R- = Remote AP requires Auth C = Cellular RAP c = CERT-based RAP 2=Using IKE version 2 X = Maintenance Mode P = PPPoE AP B = Built-in AP
Configure ip address on ctivo license#
I = Inactive H = Using 802.11n license D = Dirty or no config
Rebooted the ap.įlags: U = Unprovisioned N = Duplicate name G = No such group L = Unlicensed
0 kommentar(er)
